Heidenhain TNC 640 (34059x-04) Cycle programming Manual do Utilizador Página 265
- Página / 603
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DATUM SETTING (Cycle 247, DIN/ISO: G247) 11.4
11
TNC 640 | User's Manual Cycle Programming | 3/2014
265
11.4 DATUM SETTING (Cycle 247, DIN/ISO:
G247)
Effect
With the DATUM SETTING cycle you can activate as the new
datum a preset defined in a preset table.
After a DATUM SETTING cycle definition, all of the coordinate
inputs and datum shifts (absolute and incremental) are referenced
to the new preset.
Status display
In the status display the TNC shows the active preset number
behind the datum symbol.
Please note before programming:
When activating a datum from the preset table,
the TNC resets the datum shift, mirroring, rotation,
scaling factor and axis-specific scaling factor.
If you activate preset number 0 (line 0), then you
activate the datum that you last set in the Manual
Operation or El. Handwheel operating mode.
Cycle 247 is not functional in Test Run mode.
Cycle parameters
Number for datum?: Enter the number of the
datum to be activated from the preset table. Input
range: 0 to 65535
NC blocks
13 CYCL DEF 247 DATUM SETTING
Q339=4 ;DATUM NUMBER
Status displays
In the additional status display (POS. DISP. STATUS) the TNC shows
the active preset number behind the datum dialog.
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Software options 5
- Intended place of operation 9
- Legal information 9
- Fundamentals 10
- Contents 13
- Overviews 47
- 1.1 Introduction 48
- Available Cycle Groups 1.2 49
- 1.2 Available Cycle Groups 49
- Using Fixed Cycles 51
- 2.1 Working with fixed cycles 52
- Working with fixed cycles 2.1 53
- Using GLOBAL DEF information 57
- Entering PATTERN DEF 61
- Using PATTERN DEF 61
- Defining a single pattern 63
- Defining a full circle 65
- Point tables 2.4 67
- 2.4 Point tables 67
- Drilling 71
- 3.1 Fundamentals 72
- DRILLING (Cycle 200) 3.3 75
- 3.3 DRILLING (Cycle 200) 75
- ISO: G203) 82
- ISO: G205) 88
- 3.9 BORE MILLING (Cycle 208) 92
- BORE MILLING (Cycle 208) 3.9 93
- (Cycle 241, DIN/ISO: G241) 95
- Programming Examples 3.11 99
- Fixed Cycles: Drilling 100
- 3.11 Programming Examples 100
- Fixed Cycles: 101
- Tapping / Thread 101
- 4.1 Fundamentals 102
- (Cycle 206, DIN/ISO: G206) 103
- Cycle parameters 105
- ISO: G207) 106
- 209, DIN/ISO: G209) 109
- Prerequisites 113
- Cycle run 115
- (Cycle 263, DIN/ISO:G263) 119
- 264, DIN/ISO: G264) 123
- Q359 (incremental): 126
- (Cycle 265, DIN/ISO: G265) 127
- DIN/ISO: G267) 131
- Programming Examples 4.11 135
- 4.11 Programming Examples 135
- Fixed cycles: 137
- Pocket milling / 137
- 5.1 Fundamentals 138
- DIN/ISO: G251) 139
- ISO: G252) 143
- DIN/ISO: G256) 156
- 5.8 Programming Examples 164
- Programming Examples 5.8 165
- Pattern Definitions 167
- 6.1 Fundamentals 168
- 6.4 Programming Examples 174
- Programming Examples 6.4 175
- Contour Pocket 177
- Fixed Cycles: Contour Pocket 178
- 7.1 SL Cycles 178
- SL Cycles 7.1 179
- Superimposed contours 7.3 181
- 7.3 Superimposed contours 181
- ISO G275) 197
- Programming Examples 7.11 201
- 7.11 Programming Examples 201
- Cylindrical Surface 207
- 8.1 Fundamentals 208
- Cycle call 209
- 8.5 Programming Examples 218
- Programming Examples 8.5 219
- Defining contour descriptions 224
- Superimposed contours 226
- Contour description programs: 231
- Multipass Milling 235
- 10.1 Fundamentals 236
- ISO: G230) 237
- Q236=+25 ;4TH POINT 3RD AXIS 242
- Q240=40 ;NUMBER OF CUTS 242
- Q207=500 ;FEED RATE FOR 242
- Programming Examples 10.6 255
- 10.6 Programming Examples 255
- Cycles: Coordinate 257
- Transformations 257
- 11.1 Fundamentals 258
- (Cycle 7, DIN/ISO: G53) 260
- Configuring the datum table 264
- To exit a datum table 264
- Status displays 264
- G80, software option 1) 273
- Resetting 275
- Workspace monitoring 276
- Programming Examples 11.10 279
- 11.10 Programming Examples 279
- Cycles: Special 281
- Functions 281
- Cycles: Special Functions 282
- 12.1 Fundamentals 282
- Function 283
- ISO: G36) 286
- Cycle function 287
- 12.6 ENGRAVING (Cycle 225 290
- DIN/ISO: G225) 290
- Cycles: Turning 293
- Working with turning cycles 297
- Application 300
- (Cycle 800, DIN/ISO: G800) 301
- (Cycle 811, DIN/ISO: G811) 308
- Roughing cycle run 310
- (Cycle 812, DIN/ISO: G812) 311
- (Cycle 813, DIN/ISO: G813) 314
- TURN, LONGITUDINAL PLUNGE 315
- (Cycle 814, DIN/ISO: G814) 318
- (Cycle 810, DIN/ISO: G810) 322
- 13.10 TURN CONTOUR-PARALLEL 326
- (Cycle 815, DIN/ISO: G815) 326
- 13.11 TURN SHOULDER FACE 330
- (Cycle 821, DIN/ISO: G821) 330
- (Cycle 822, DIN/ISO: G822) 332
- TURN SHOULDER FACE EXTENDED 333
- (Cycle 823, DIN/ISO: G823) 336
- TURN, TRANSVERSE PLUNGE 337
- (Cycle 824, DIN/ISO: G824) 340
- 13.15 TURN CONTOUR FACE 344
- (Cycle 820, DIN/ISO: G820) 344
- (Cycle 841, DIN/ISO: G841) 348
- SIMPLE RADIAL RECESSING 349
- (Cycle 842, DIN/ISO: G842) 350
- RADIAL RECESSING EXTENDED 351
- (Cycle 840, DIN/ISO: G840) 354
- RECESSING CONTOUR RADIAL 355
- 13.19 SIMPLE AXIAL RECESSING 358
- (Cycle 851, DIN/ISO: G851) 358
- SIMPLE AXIAL RECESSING 359
- (Cycle 852, DIN/ISO: G852) 362
- AXIAL RECESSING EXTENDED 363
- 13.21 AXIAL RECESSING 366
- (Cycle 850, DIN/ISO: G850) 366
- AXIAL RECESSING 367
- 13.22 RADIAL RECESSING 370
- (Cycle 861, DIN/ISO: G861) 370
- RADIAL RECESSING 371
- (Cycle 862, DIN/ISO: G862) 372
- (Cycle 860, DIN/ISO: G860) 376
- 13.25 AXIAL RECESSING 380
- (Cycle 871, DIN/ISO: G871) 380
- (Cycle 872, DIN/ISO: G872) 382
- 13.27 AXIAL RECESSING 386
- (Cycle 870, DIN/ISO: G870) 386
- 13.28 THREAD LONGITUDINAL 390
- (Cycle 831, DIN/ISO: G831) 390
- THREAD LONGITUDINAL 391
- ISO: G832) 392
- =0 ISO 1502 394
- 13.30 CONTOUR-PARALLEL THREAD 396
- (Cycle 830, DIN/ISO: G830) 396
- CONTOUR-PARALLEL THREAD 397
- 13.31 Example program 400
- Example program 13.31 401
- Using Touch Probe 403
- Using Touch Probe Cycles 404
- Probe Cycles 407
- Multiple measurements 409
- Touch probe table 14.3 411
- 14.3 Touch probe table 411
- Touch Probe 413
- Cycles: Automatic 413
- Measurement 413
- Misalignment 413
- 15.1 Fundamentals 414
- Fundamentals 15.1 415
- (Cycle 401, DIN/ISO: G401) 419
- (Cycle 402, DIN/ISO: G402) 422
- ISO: G403) 426
- ISO: G404) 428
- (Cycle 405, DIN/ISO: G405) 430
- Datum Setting 435
- 16.1 Fundamentals 436
- Fundamentals 16.1 437
- ISO: G408) 440
- DIN/ISO: G409) 444
- (Cycle 410, DIN/ISO: G410) 447
- Q384=+0 ;3RD CO. FOR TS AXIS 450
- Q333=+1 ;DATUM 450
- 16.5 DATUM FROM OUTSIDE OF 451
- RECTANGLE (Cycle 411, DIN/ 451
- ISO: G411) 451
- (Cycle 412, DIN/ISO: G412) 454
- (Cycle 413, DIN/ISO: G413) 459
- (Cycle 414, DIN/ISO: G414) 463
- (Cycle 415, DIN/ISO: G415) 468
- DIN/ISO: G416) 472
- Q382=+85 ;1ST CO. FOR TS AXIS 475
- Q383=+50 ;2ND CO. FOR TS AXIS 475
- Q320=0 ;SET-UP CLEARANCE 475
- 417, DIN/ISO: G417) 476
- 418, DIN/ISO: G418) 478
- ISO: G419) 482
- Workpiece 489
- Inspection 489
- 17.1 Fundamentals 490
- Fundamentals 17.1 491
- DIN/ISO: G422) 504
- 17.7 MEASURE RECTANGLE INSIDE 507
- (Cycle 423, DIN/ISO: G423) 507
- (Cycle 424, DIN/ISO: G424) 510
- DIN/ISO: G425) 513
- DIN/ISO: G426) 516
- DIN/ISO: G427) 519
- (Cycle 430, DIN/ISO: G430) 522
- Q309=0 ;PGM STOP IF ERROR 524
- Q330=0 ;TOOL 524
- 17.14 Programming Examples 528
- Programming Examples 17.14 529
- 18.1 Fundamentals 532
- MEASURE (Cycle 3) 18.2 533
- 18.2 MEASURE (Cycle 3) 533
- DIN/ISO: G461) 541
- 462, DIN/ISO: G462) 542
- (Cycle 463, DIN/ISO: G463) 544
- Kinematics 547
- Overview 549
- 19.2 Prerequisites 550
- DIN/ISO: G450, option) 551
- Logging function 552
- Notes on data management 553
- DIN/ISO: G451, option) 554
- Positioning direction 556
- Notes on the accuracy 559
- Backlash 561
- Various modes (Q406) 566
- DIN/ISO: G452, option) 568
- Drift compensation 575
- Tool Measurement 579
- 20.1 Fundamentals 580
- Fundamentals 20.1 581
- Tables of Cycles 595
- 21.1 Overview 596
- Overview 21.1 597
- Touch probes from HEIDENHAIN 603
Manuais e produtos relacionados com Equipamento Heidenhain TNC 640 (34059x-04) Cycle programming
(607 páginas)
(615 páginas)
(623 páginas)
(627 páginas)
(645 páginas)
(647 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais